Search results

• Atari 7800 Hardware
  A peculiarity of 7800 motherboards is that the top and bottom of the boards may have diferent revision labels. The top of this board is labeled 'CA025234' and the bottom is labeled 'CA025233-002
  1 KB (207 words) - 07:54, 6 July 2021
• 3DO FZ-10 Hardware
  FZ-10 top 01.jpg FZ-10 top front angle.jpg
  2 KB (327 words) - 08:12, 6 July 2021
• Atari Video Pinball
  Board Top Splice.jpg|Atari Video Pinball board, top view
  1,009 bytes (153 words) - 18:58, 5 December 2020
• ColecoVision Teardown
  ...le is fairly straightforward with the only complication being removing the top of the case. ==Step 2 - Remove the top==
  5 KB (975 words) - 20:39, 25 January 2014
• Sega CD
  |imagecaption = '''Top:''' Model 1 Sega CD & Model 1 Sega Genesis<br/>'''Bottom:''' Model 2 Sega C ...rive console and loads CDs via a motorized tray. A second version places a top-loading CD-ROM drive to the right of the console and is intended primarily
  1 KB (209 words) - 07:19, 13 April 2022
• Neo-Geo
  Neo Geo AES top front angle.jpg|Top angle, from the front. Neo Geo AES top rear angle.jpg|Top angle, from the back.
  4 KB (684 words) - 03:41, 13 April 2022
• TurboGrafx-16/PC Engine
  TurboGrafX-16 TurboPad top.jpg TurboGrafX-16 top.jpg
  2 KB (351 words) - 06:51, 12 April 2022
• Atari 2600 Hardware
  [[File:2600jr_board_top.jpg|thumb|Top of motherboard]]
  836 bytes (117 words) - 07:53, 6 July 2021
• Main Page
  |- valign="top" |- valign="top"
  5 KB (607 words) - 08:08, 6 July 2021
• Atari 7800 Teardown
  ...ch are circled in the picture. Turn it back over and lift the top off. The top should come off effortlessly. |Here is the underside of the top of the case. The buttons can be removed easily by pushing the small plastic
  7 KB (1,190 words) - 20:38, 25 January 2014
• Expansion Pak
  ...n for the [[Nintendo 64]] console, released in 1998. When plugged into the top of the console it upgrades the Random Access Memory (RAM) from 4MB to 8MB,
  718 bytes (116 words) - 08:51, 12 April 2022
• Sega Genesis II Teardown
  ...crews to come all the way out of their holes. Once the screws are out, the top cover should lift straight up from the base. Set the base of the console aside and turn over the top plastic cover. Undo the three bronze-colored screws highlighted in the pict
  4 KB (774 words) - 20:26, 30 January 2014
• Sega Master System
  Sega Master System top.jpg Sega Master System top front angle.jpg
  5 KB (849 words) - 16:25, 13 April 2022
• Conic
  If you open the chassis on this console and remove the top cover, you can push the game selection slide switch two steps further to en | class="pageHeading" valign="top"|
  4 KB (602 words) - 11:06, 30 December 2020
• ColecoVision Hardware
  Coleco-revH2 board top.jpg|revH2, top Coleco revH2-1 board top.jpg|revH2-1, top
  6 KB (791 words) - 08:13, 6 July 2021
• Nintendo Entertainment System
  *The Famicom featured a top-loading cartridge slot, a 15-pin expansion port located on the unit’s fro ...ly common throughout Japan and the Far East. The original NES (but not the top-loading NES-101) contained the [[10NES]] lockout chip, which increased the
  9 KB (1,357 words) - 19:26, 14 April 2022
• 3DO Interactive Multiplayer
  [[File:FZ-10 top front angle.jpg|150px|right]] The Panasonic FZ-10 is an updated top-loading version of the FZ-1. The controllers were made smaller and lighter,
  7 KB (1,045 words) - 09:01, 12 April 2022
• Entex Adventure Vision
  ...and Space Force. All four games could be stored in a little compartment on top of the system.
  3 KB (400 words) - 18:49, 5 December 2020
• Coleco Telstar
  ...right sides of case, pinball launch button and field adjustment sliders on top, light gun, uses a MOS Technology MPS 7600-004 chip.
  3 KB (429 words) - 14:16, 30 December 2020
• Virtual Boy
  ...roller = 1 NES controller protocol}}The Virtual Boy (バーチャルボーイ) was a table-top video game console developed and manufactured by Nintendo. It was the first
  3 KB (369 words) - 20:42, 18 January 2014

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)